Silverback

Fully CNC steel QD attachment point for SRS handguards (Covert and long) with dark grey phosphating finish. This attachement point allows you to fix your QD sling at the desired position on your handguard. 2 x M4x12 included. Read more

MDRX/AR15 Magazine, 120 rds

PA6 Nylon fiberglass reinforced magazine,

Available in:

-Black: SBA-MAG-51BK

-FDE: SBA-MAG-51FDE Read more

SBA-STK-37BK Read more

MRDX Pin puncherPin puncher specifically designed to disassembly your MDRX without over-pushing the pins.

SBA-TWS-51 Read more

Microswitch based trigger PCB, hall sensor-based selector (single/full auto).SBA-ELE-51 Read more

O-rings set for the MDRX, including each o-ring inside the gun and the gearbox.2×1 70° NBR – 1 piece
6×2 70° NBR – 1 piece
8×1.8 FKM – 1 piece
8×2 70° NBR – 2 pieces
8×2 PU – 1 piece
22×2 FKM – 1 piece
25×1 70° NBR – 1 piece

SBA-ORG-54 Read more

Polycarbonate hop-up unit for AEG hop-up rubbers, TCD ring design, incremental “click” adjustments using 2 ball plungers, 36 positions ranging from 0 up to 750 µm with the low nub (standard bbs configuration), and from 500 up to 1250 µm with the high nub Read more

-PCB control board, cycle detection based on Hall effect sensor.-2 Mosfet for power, 1 for active braking.

-Powered either by 11.1 or 7.2 V battery.

SBA-ELE-50 Read more

Initially designed for the MDRX hop-up, this  rubber can fit inside most of airsoft guns using “AEG” hop-up rubber.5 dot lips design for bbs feeding, flat contact patch, similar to our SRS-TAC41 and GBB hop-up rubbers

Blue colour, 50° hardness, 4 pieces. Read more

Set of colored polymer parts for TAC-41 A, it includes part numbers:T41-1102
T41-1103
T41-1117
T41-1118 (x2)
T41-1119
Available in 4 colors:

Black stock: SBA-STK-36BK
FDE stock: SBA-STK-36FDE
Green stock: SBA-STK-36OD
Wolf Grey stock: SBA-STK-36WG Read more

TAC-41 match trigger,6000 series aluminium, CNC, Black and Red hard anodized, mounted on two 10×4 ball bearings.

Steel trigger blade axis.

This trigger allows the following adjustments:

– trigger blade height
– trigger blade angle

Weight: 20 Grams Read more

SRS ABS light magazine 25 roundsColours: FDE, OD, black, smoke Read more

“AEG” cut inner barrel, passivated brass, 6.05 mm bore, 330 mm long,
Ideal for:

– “330 mm” TAC-41 outer barrel used with “AEG” hopup unit. Read more

“GBB” type, flat hopup rubber, 4 hardness set (50°/60°/70°/80°)
Initially designed for the TAC-41 “GBB” hopup, this hopup rubber can fit inside most of airsoft guns using “GBB” hopup rubber.

Transparent silicone for easier installation, this kit include Read more

This adapter is threaded in 1/4-20 UNC. It can be mounted on the tripod mount of the SRS-A2, SRS-A2M2, and TAC-41 P.It allows to fix either a Harris bipod or a sling swivel in a backward position, closer to the center of gravity of the rifle.
Stainless st Read more

SRS A2/M2, M2 top rail, short Read more

TAC 41 Trigger Guard Assembly Read more

TAC 41 Piston Read more

DTSS QD replica .300 (24mm CW) + SBA-FHD-06 Read more

5.8x0.75mm O-rings for HOP-14/15 (10 pieces) Read more

SRS A2 Sport handguard Nylon FDE Read more

HTI cylinder Read more

SRS Hollow Buttplate Spacer | For Pull boltReinforced Nylon fiber hollow buttplate spacer (SRS214) for the Silverback SRS-A1, allowing you to use a pull bolt.Desert Tech licensed product. Read more

SRS Dual Stage Trigger - Match Read more